1994 Chevrolet C10 Recalls

1. Recall Description

   VEHICLE DESCRIPTION: PICKUP TRUCKS, CREW CABS, UTILITY TRUCKS AND SPORT UTILITY VEHICLES. THESE VEHICLES WERE BUILT WITH THE POLARITY OF THE WIRING FOR THE ZERO ADJUST BRAKE SWITCH REVERSED FROM WHAT WAS SPECIFIED ON THE SWITCH DRAWING. WITH THE REVERSED POLARITY, THE CONTACTS IN THE BRAKE SWITCH CAN WEAR OUT PREMATURELY. THE BRAKE SWITCH WILL PERFORM NORMALLY UNTIL THE BRAKE SWITCH CONTACTS WEAR OUT, RESULTING IN LOSS OF THE BRAKE LAMPS WITHOUT ANY WARNING TO THE DRIVER.

   Possible Effects

   THIS WOULD FAIL TO WARN A FOLLOWING DRIVER THAT THE VEHICLE IS BRAKING AND COULD LEAD TO A CRASH.

   Action

   DEALERS WILL REPLACE THE BRAKE SWITCH AND REVERSE THE WIRING.

   Notes

   OWNER NOTIFICATION BEGAN APRIL 12, 1999.OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782.ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION''S AUTO SAFETY HOTLINE AT 1-888-DASH-2-DOT (1-888-327-4236).

   Recall Manufacture Dates

   1993-03-01 - 1994-09-30

   Vehicles Affected

   988587

2. Recall Description

   VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND SPORT UTILITY VEHICLES, 2 AND 4-WHEEL DRIVE. SOLDER JOINTS NEAR THE WIRING HARNESS CONNECTOR CAN CRACK CAUSING THE WINDSHIELD WIPERS TO WORK INTERMITTENTLY.

   Possible Effects

   THIS CONDITION CAN RESULT IN INOPERATIVE WIPERS, REDUCING A DRIVER''S VISIBILITY, AND INCREASING THE RISK OF A VEHICLE CRASH.

   Action

   DEALERS WILL REPLACE THE WIPER MOTOR CIRCUIT BOARD AND COVER.

   Notes

   OWNER NOTIFICATION BEGAN DECEMBER 15, 1998.OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782.ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION''S AUTO SAFETY HOTLINE AT 1-888-DASH-2-DOT (1-888-327-4236).

   Recall Manufacture Dates

   1994-08-01 - 1996-05-31

   Vehicles Affected

   1557585

3. Recall Description

   VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS, VANS AND MOTORHOMES EQUIPPED WITH ELECTRONICALLY FUEL INJECTED 6.5L DIESEL ENGINE. THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH FEDERAL REGULATION PART 573. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. THE CAMPAIGN WILL IMPROVE THE OVERALL DRIVEABILITY OF THESE VEHICLES.

   Possible Effects

   CERTAIN VEHICLES CAN EXHIBIT SOME DRIVEABILITY CONCERNS SUCH AS POOR THROTTLE RESPONSE, STALLING, MISFIRE, POOR HOT OR COLD STARTING, EXTENDED CRANKING OF A HOT ENGINE, OR STALLING AFTER START. TRUCKS WITH MANUALTRANSMISSIONS CAN EXHIBIT POOR ACCELERATION FROM START OR COULD STALL DURING DECELERATION.

   Action

   DEALERS WILL INSTALL SOME RECENTLY DEVELOPED ENHANCEMENTS WHICH WILL IMPROVE THE OVERALL DRIVEABILITY OF THESE VEHICLES.

   Notes

   GENERAL MOTORS HAS DECIDED TO CONDUCT A SAFETY IMPROVEMENT SERVICE CAMPAIGN TO IMPROVE THE DRIVEABILITY OF THESE VEHICLES. OWNERS CAN CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782.

   Recall Manufacture Dates

   1993-08-01 - 1994-07-01

   Vehicles Affected

   60000

4. Recall Description

   THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLE COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

   Possible Effects

   IF THIS WERE TO OCCUR TO THE DRIVER''S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.

   Action

   DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER''S AND PASSENGER''S SEATS.

   Notes

   SYSTEM: INTERIOR; SEAT TRACK ANCHORS AND SEAT.VEHICLE DESCRIPTION: LIGHT DUTY PICKUP EXTENDED CAB TRUCKS EQUIPPED WITH FRONT HIGH-BACK BUCKET SEATS OR 60/40 SPLIT BENCH SEATS.NOTE: OWNERS WHO TAKE THEIR VEHICLE TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782. ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION''S AUTO SAFETY HOTLINE AT 1-800-424-9393.

   Recall Manufacture Dates

   1992-06-01 - 1994-09-01

   Vehicles Affected

   675661

5. Recall Description

   IF BOTH THE LAP-BELT AND SHOULDER-BELT ENERGY MANAGEMENT LOOPS ON THE FRONT SEAT BELT ASSEMBLIES RELEASE AT OR NEAR THE SAME TIME, ACCELERATION FORCES CAN CAUSE THE BUCKLE RELEASE MECHANISM TO ACTIVATE AND ALLOW THE BUCKLE TO SEPARATE FROM THE LATCH.

   Possible Effects

   IF THE BUCKLE RELEASED, THE SYSTEM WOULD FAIL TO PROVIDE ADEQUATE OCCUPANT RESTRAINT PROTECTION.

   Action

   DEALERS WILL REMOVE THE STITCHING THAT CREATES THE ENERGY MANAGEMENT LOOP IN THE SHOULDER BELT(S).

   Notes

   SYSTEM: INTERIOR; SEAT BELTS; FRONT.VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS, EXTENDED CAB, EQUIPPED WITHGAS ENGINES OR 6.5L H.O. TURBO DIESEL ENGINES.NOTE: OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782. ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION''S AUTO SAFETY HOTLINE AT 1-800-424-9393.

   Recall Manufacture Dates

   1993-03-01 - 1995-07-01

   Vehicles Affected

   630099

6. Recall Description

   THESE VEHICLES WERE BUILT WITH FRONT SEAT BELT SYSTEMS WITH NO ENERGY MANAGEMENT LOOPS AND MAY NOT MEET THE HEAD INJURY CRITERIA REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."

   Possible Effects

   IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANTS OF THESE SEATS MAY NOT BE PROPERLY RESTRAINED.

   Action

   DEALERS WILL REPLACE THE RETRACTOR PORTION OF THE SEAT BELT ASSEMBLY(S) WITH ONE HAVING THE NEWLY DESIGNED ENERGY-MANAGEMENT TWIN-LOOP SYSTEM.

   Notes

   SYSTEM: INTERIOR; SEAT BELTS; FRONT, FMVSS NO. 208.VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS, WITH EXTENDED CABS, AND EQUIPPED WITH 6.5L NATURALLY ASPIRATED DIESEL ENGINES AND 6.5L TURBO DIESEL ENGINES.NOTE: OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782. ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION''S AUTO SAFETY HOTLINE AT 1-800-424-9393.

   Recall Manufacture Dates

   1993-03-01 - 1995-07-01

   Vehicles Affected

   40

7. Recall Description

   THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLES COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

   Possible Effects

   IF THIS WERE TO OCCUR TO THE DRIVER''S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.

   Action

   DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER''S AND PASSENGER''S SEATS.

   Notes

   SYSTEM: INTERIOR; SEAT TRACK ANCHORS AND SEAT.EQUIPMENT DESCRIPTION: FRONT HIGH-BACK BUCKET SEATS OR 60/40 SPLIT BENCH SEATS PROVIDED BY VEHICLE SAFETY SYSTEMS FOR INSTALLATION IN LIGHT DUTY PICKUP EXTENDED CAB CONVERSION TRUCKS.NOTE: OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME, SHOULD CONTACT VSS AT 1-800-742-5043. ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION''S AUTO SAFETY HOTLINE AT 1-800-424-9393.

   Recall Manufacture Dates

   1994-07-01 - 1996-02-01

   Vehicles Affected

   2400

8. Recall Description

   THE WINDSHIELDS WERE INSTALLED WITH INCORRECT WINDSHIELD OPENING PINCH-WELD-FLANGE PRIMER. THIS PRIMER WILL NOT PROPERLY ETCH THE PAINTED SURFACE OF THE FLANGE, ALLOWING THE WINDSHIELD TO SEPARATE FROM THE VEHICLE DURING A COLLISION. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 212, "WINDSHIELD MOUNTING."

   Possible Effects

   CONSEQUENCE OF NON-COMPLIANCE: THE SEPARATION OF THE WINDSHIELD FROM THE VEHICLE DURING COLLISION INCREASES THE RISK OF INJURY FOR ALL PERSONS INVOLVED.

   Action

   DEALERS WILL REMOVE THE WINDSHIELD AND REINSTALL IT USING THE CORRECT PRIMER.

   Notes

   SYSTEM: VISUAL SYSTEMS; GLASS; WINDSHIELD.VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS.NOTE: IF THE VEHICLE IS PRESENTED TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND THE REMEDY IS NOT PROVIDED FREE OF CHARGE WITHIN A REASONABLE TIME OR THE REMEDY DOES NOT CORRECT THE NONCOMPLIANCE, PLEASE CONTACT CHEVROLET AT 1-800-222-1020; OR GMC AT 1-810-456-4547. ALSO, CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION''S AUTO SAFETY HOTLINE AT 1-800-424-9393.

   Recall Manufacture Dates

   1994-08-01 - 1994-08-01

   Vehicles Affected

   29

9. Recall Description

   THE BRAKE PEDAL PUSH ROD RETAINER IS MISSING, MISPOSITIONED OR NOT PROPERLY SEATED.

   Possible Effects

   BRAKE PEDAL PUSH ROD PROBLEMS CAN CAUSE THE STOP LAMPSWITCH AND THE BRAKE BOOSTER PUSH ROD TO DISCONNECT FROM THE BRAKE PEDAL,RESULTING IN LOSS OF BRAKE OPERATION, AND A VEHICLE CRASH COULD OCCUR WITHOUTPRIOR WARNING.

   Action

   INSPECT VEHICLES TO ASSURE THE BRAKE PEDAL PUSH ROD RETAINER IS PRESENT AND FULLY SEATED IN ITS CORRECT POSITION.

   Notes

   SYSTEM: BRAKES; HYDRAULIC; LINKAGE.VEHICLE DESCRIPTION: LIGHT TRUCKS AND VANS.NOTE: IF YOUR VEHICLE IS PRESENTED TO AN AUTHORIZED DEALER ON AN AGREED UPONSERVICE DATE AND THE REMEDY IS NOT PROVIDED WITHIN A REASONABLE TIME AND FREEOF CHARGE OR THE REMEDY DOES NOT CORRECT THE DEFECT OR NONCOMPLIANCE, PLEASECONTACT EITHER THE CHEVROLET SERVICE CENTER AT 1-800-222-1020 OR GMC SERVICECENTER AT 1-313-456-4547. ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETYADMINISTRATION''S AUTO SAFETY HOTLINE AT 1-800-424-9393.

   Recall Manufacture Dates

   1993-07-01 - 1993-08-01

   Vehicles Affected

   70154

10. Recall Description

    THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, "SEATING SYSTEMS."

    Possible Effects

    THE MISSING BOLTS MAY CAUSE THE DRIVER''S SEAT TO BECOMELOOSE AND IN A SUDDEN STOP OR ACCIDENT MAY SUBJECT THE OCCUPANT TO INCREASEDRISK OF INJURY.

    Action

    DEALERS WILL INSPECT SEATS FOR MISSING BOLTS AND INSTALL BOLTS IF REQUIRED.

    Notes

    SYSTEM: INTERIOR SYSTEMS; SEAT TRACK ANCHORS; FMVSS 207.VEHICLE DESCRIPTION: 1/2 TON, 3/4 TON AND 1 TON PICKUP TRUCKS, EXTENDED CAB ANDCHASSIS CAB MODELS WITH BENCH SEAT, 60/40 SPLIT SEAT OR HIGH BACK BUCKET SEATS.NOTE: IF YOUR VEHICLE IS PRESENTED TO AN AUTHORIZED DEALER ON AN AGREED UPONSERVICE DATE AND THE REMEDY IS NOT PROVIDED WITHIN A REASONABLE TIME AND FREEOF CHARGE OR THE REMEDY DOES NOT CORRECT THE DEFECT OR NONCOMPLIANCE, PLEASECONTACT CHEVROLET SERVICE CENTER AT 1-800-222-1020 OR GMC SERVICE CENTER AT1-313-456-4547. ALSO, CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETYADMINISTRATION''S AUTO SAFETY HOTLINE AT 1-800-424-9393.

    Recall Manufacture Dates

    -

    Vehicles Affected

    1375

11. Recall Description

    TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.

    Possible Effects

    IF THIS OCCURS, A LOSS OF VEHICLE CONTROL AND A CRASH COULD RESULT.

    Action

    DEALERS WILL TIGHTEN THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TO THE PROPER TORQUE SPECIFICATION.

    Notes

    SYSTEM: SUSPENSION; INDEPENDENT FRONT CONTROL ARM; LOWER.VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS.NOTE: IF YOUR VEHICLE IS PRESENTED TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND THE REMEDY IS NOT PROVIDED IN A REASONABLE AMOUNT OF TIME AND FREE OF CHARGE OR THE REMEDY DOES NOT CORRECT THE DEFECT OR NONCOMPLIANCE, PLEASE CONTACT CHEVROLET AT 1-800-222-1020, OR GMC AT 1-313-456-4547. ALSO, PLEASE CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION''S AUTO SAFETY HOTLINE AT 1-800-424-9393.

    Recall Manufacture Dates

    1993-11-01 - 1993-12-01

    Vehicles Affected

    30148

12. Recall Description

    CERTAIN AAI MOTORSPORTS COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LIST PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

    Possible Effects

    LACK OF AMBER SIDE REFLECTORS IN THE LAMPS WILL DECREASE LIGHTING VISIBILITY TO OTHER DRIVERS AND MAY POSSIBLY RESULT IN A VEHICLE CRASH

    Action

    AAI MOTORSPORTS WILL NOTIFY OWNERS AND REPLACE THE LAMPS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 1, 2006. OWNERS MAY CONTACT AAI MOTORSPORTS AT 909-923-9188.

    Notes

    THIS RECALL ONLY PERTAINS TO AAI MOTORSPORTS AFTERMARKET LAMPS AND HAS NO RELATION TO ANY ORIGINAL EQUIPMENT INSTALLED ON THE LISTED PASSENGER VEHICLES.FOR MORE INFORMATION ON THE LAMP MODEL NUMBERS, CLICK ON DOCUMENT SEARCH AND VIEW DOCUMENT TITLED "LAMP MODEL NUMBERS."CUSTOMERS MAY CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION''S VEHICLE SAFETY HOTLINE AT 1-888-327-4236 (TTY: 1-800-424-9153); OR GO TO HTTP://WWW.SAFERCAR.GOV.

    Recall Manufacture Dates

    -

    Vehicles Affected

    87745

13. Recall Description

    K2 MOTOR IS RECALLING 1,921 AFTERMARKET HEADLAMPS OF VARIOUS MODELS SOLD FOR USE ON THE ABOVE LISTED VEHICLES. THESE HEADLAMPS ARE MISSING THE AMBER SIDE REFLEX REFLECTOR WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

    Possible Effects

    WITHOUT THE AMBER SIDE REFLEX REFLECTORS, THE LIGHTING VISIBILITY MAY BE AFFECTED, POSSIBLY RESULTING IN A VEHICLE CRASH.

    Action

    K2 MOTOR WILL NOTIFY OWNERS AND OFFER A FULL REFUND. THE RECALL BEGAN ON DECEMEBER 17, 2008. OWNERS MAY CONTACT K2 MOTOR AT 1-909-839-2992.

    Notes

    THIS RECALL ONLY PERTAINS TO AFTERMARKET REPLACEMENT EQUIPMENT AND HAS NO RELATION TO ANY ORIGINAL EQUIPMENT INSTALLED ON VEHICLES MANUFACTURED BY HONDA, FORD, OR CHRYSLER LLC. CUSTOMERS MAY CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION''S VEHICLE SAFETY HOTLINE AT 1-888-327-4236 (TTY: 1-800-424-9153); OR GO TO HTTP://WWW.SAFERCAR.GOV.

    Recall Manufacture Dates

    -

    Vehicles Affected

    1921

14. Recall Description

    SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

    Possible Effects

    DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.

    Action

    SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.

    Notes

    THIS RECALL ONLY PERTAINS TO AFTERMARKET REPLACEMENT EQUIPMENT AND HAS NO RELATION TO ANY ORIGINAL EQUIPMENT INSTALLED ON VEHICLES PRODUCED BY THE VEHICLE MANUFACTURER.IN ORDER TO DETERMINE IF YOUR AFTERMARKET LAMP ASSEMBLY IS AFFECTED BY THIS NONCOMPLIANCE, PLEASE REVIEW THE LIST OF MODEL NUMBERS PROVIDED TO US BY SABERSPORT.THE LIST CAN BE FOUND UNDER "DOCUMENT SEARCH" LOCATED AT THE BOTTOM OF YOUR SCREEN.OWNERS MAY ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION''S VEHICLE SAFETY HOTLINE AT 1-888-327-4236 (TTY 1-800-424-9153), OR GO TO <A HREF=HTTP://WWW.SAFERCAR.GOV>HTTP://WWW.SAFERCAR.GOV</A> .

    Recall Manufacture Dates

    -

    Vehicles Affected

    16270

15. Recall Description

    DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

    Possible Effects

    DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.

    Action

    DOPE, INC. WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON JULY 28, 2009. OWNERS MAY CONTACT DOPE, INC. AT 1-626-272-1798.

    Notes

    THIS RECALL ONLY PERTAINS TO AFTERMARKET REPLACEMENT EQUIPMENT AND HAS NO RELATION TO ANY ORIGINAL EQUIPMENT INSTALLED ON VEHICLES PRODUCED BY THE VEHICLE MANUFACTURER.IN ORDER TO DETERMINE IF YOUR AFTERMARKET LAMP ASSEMBLY IS AFFECTED BY THIS NONCOMPLIANCE, PLEASE REVIEW THE LIST OF MODEL NUMBERS PROVIDED TO US BY DOPE, INC.THE LIST CAN BE FOUND UNDER "DOCUMENT SEARCH" LOCATED AT THE BOTTOM OF YOUR SCREEN. OWNERS MAY ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION''S VEHICLE SAFETY HOTLINE AT 1-888-327-4236 (TTY 1-800-424-9153), OR GO TO <A HREF=HTTP://WWW.SAFERCAR.GOV>HTTP://WWW.SAFERCAR.GOV</A> .

    Recall Manufacture Dates

    -

    Vehicles Affected

    42540